/*
 * DPT 3334 SCSI Host Adapter.
 * Version 0.9 - Sat Apr 5, 1997 - John L. Chmielewski, jlc@att.com
 * Needs work:
 *	handle multiple controllers;
 */
#include "u.h"
#include "../port/lib.h"
#include "mem.h"
#include "dat.h"
#include "fns.h"
#include "io.h"
#include "../port/error.h"

#define ETA_SIG		(((long) 'E') | (((long) 'A') << 8) |\
			(((long) 'T') << 16) | (((long) 'A') << 24))

enum {
	Nctl		= 1,		/* Max # of Controllers		*/
	CtrlID		= 7,		/* Default Controller ID	*/
	NTarget		= 16,		/* Max targets/controller-chan	*/
	Timeout		= 10,		/* Timeout in seconds		*/
	SenLen		= 0xFF,		/* Maximum Sense Data Length	*/
	PCIvid		= 0x1044,	/* PCI Vendor ID: DPT		*/
	PCIdid		= 0xA400,	/* PCI Device ID: DPT		*/
};

enum {	/* Eata Register Commands */
	ReadCfg		= 0xFD,		/* Read Configuration Data, DMA */
	SendCP		= 0xFF,		/* Execute Command, DMA		*/
	Reset		= 0xF9,		/* Reset Controller		*/
};

enum {	/* Eata Register Sets - PCI */
	Cmd		= 0x17,		/* Command Register (write)	*/
	CP3		= 0x15,		/* CP Address (MSB) (write)	*/
	CP2		= 0x14,		/* CP Address (MSB -1) (write)	*/
	CP1		= 0x13,		/* CP Address (MSB-2) (write)	*/
	CP0		= 0x12,		/* CP Address (LSB) (write)	*/
	ASR		= 0X18,		/* Aux Status Register (read)	*/
	SR		= 0x17,		/* Status Register (read)	*/
	DR		= 0x10,		/* 16 bit Data Register (read)	*/
};

enum {	/* Eata Register Sets Bits */
	/* Status Register */
	ERROR		= 0x01,		/* Command ended in error	*/
	DRQ		= 0x08,		/* Drive is Ready		*/
	SC		= 0x10,		/* Seek Complete		*/
	RDY		= 0x40,		/* Active data request		*/
	BSY		= 0x80,		/* Controller busy - clear IRQ	*/
	/* Aux Status Register */
	ABSY		= 0x01,		/* Controller busy		*/
	IRQ		= 0x02,		/* Drive interrupt asserted	*/
};

/*
 * DPT DMA Status Packet
 * Big Endian Format
 */
typedef struct DPTstat DPTstat;
struct DPTstat {
	uchar		info;		/* Bits defined			*/
	uchar		sbs;		/* SCSI Bus Status		*/
	uchar		reserved0[2];
	ulong		irl;		/* Bytes Not Transfered		*/
	ulong		va;		/* Virtual Address of CP	*/
	uchar		idmsg;
	uchar		quemsg;
	uchar		tagmsg;
	uchar		msg[9];
};

enum {	/* Status Packet bits */
	/* info byte bits */
	CS		= 0x7F,		/* Controller Status		*/
	EOC		= 0x80,		/* End of Command - not safe	*/
};

/*
 * EATA Command Packet
 *
 */
typedef struct EATAcp EATAcp;
struct EATAcp {
	uchar	control;	/* Bits defined				*/
	uchar	ReqSenLen;	/* AutoRequestSense Data length		*/
	uchar	reserved1[3];
	uchar	FWNest;		/* Firmware Nested Byte for RAID	*/
	uchar	PhsUnit;	/* Physical Byte for RAID		*/
	uchar	device;		/* Bits defined				*/
	uchar	msg[4];		/* Identify and Disconnect Message	*/
	uchar	CDB[12];	/* Total SCSI CDB			*/
	ulong	DTL;		/* Byte Swapped Data Length In Bytes	*/
	ulong   va;		/* Command Packet Virtual Address	*/
	ulong	dataDMA;	/* Byte Swapped Data Physical Address	*/
	ulong	statDMA;	/* Byte Swapped Status Packet Physical	*/
	ulong	reqDMA;		/* Byte Swapped AutoRequestSense Phys	*/
};

enum {	/* Command Packet bits */
	/* control byte bits */
	Sreset		= 0x01,		/* Issue A SCSI Bus Reset	*/
	Init		= 0x02,		/* ReInitialize The Controller	*/
	ReqSen		= 0x04,		/* Do Auto Request Sense	*/
	SG		= 0x08,		/* Data Pointer To S.G. List	*/
	Quick		= 0x10,		/* Quick PIOin, DMA in/out	*/
	Interpret	= 0x20,		/* CDB Interpreted By Controller */
	DataOut		= 0x40,		/* Data Out Phase With Command	*/
	DataIn		= 0x80,		/* Data In Phase With Command	*/
	/* device byte bits */
	id		= 0x1F,		/* SCSI Target ID		*/
	Channel		= 0xE0,		/* HBA Channel Number		*/
	/* Message byte 0 bits */
	MsgLun		= 0x07,		/* Message Lun			*/
	MsgLuntar	= 0x20,		/* Target Routine		*/
	MsgDisPri	= 0x40,		/* Disconnect Reconnect		*/
	MsgIdent	= 0x80,		/* Indentify			*/
};

/*
 * ReadConfig Data Structure - This Structure Contains The EATA Configuration
 * Big Endian Format
 */
typedef struct DPTcfg DPTcfg;
struct DPTcfg {
	/* Extra bytes returned form a SCSI Inquiry Command */
	uchar	DevType;
	uchar	PageCode;
	uchar	reserved2;

	uchar	ConfigLength;	/* Length In Bytes After This Field	*/
	ulong	EATAsig;	/* EATA Signature Bytes			*/
	uchar	EATAver;	/* EATA Version Number			*/
	uchar	byte9;		/* Bits defined				*/
	ushort	PadLen;		/* Pad Bytes For PIO Commands		*/
	uchar	reserved3;
	uchar	Chan2;		/* Channel 2 SCSI ID			*/
	uchar	Chan1;		/* Channel 1 SCSI ID			*/
	uchar	Chan0;		/* Channel 0 SCSI ID			*/
	ulong	CPlength;	/* Command Packet Length		*/
	ulong	SPlength;	/* Status Packet Length			*/
	ushort	QueueSize;	/* Controller Queue Depth		*/
	uchar	reserved4[2];
	ushort	SG_Size;	/* Maximum Scatter Gather List Size	*/
	uchar	byte30;		/* Bits defined				*/
	uchar	IRQ;		/* IRQ address				*/
	uchar	byte32;		/* Bits defined				*/
	uchar	byte33;		/* Bits defined				*/
	uchar	MaxLUN;		/* Maximum SCSI LUN Supported		*/
	uchar	byte35;		/* Bits defined				*/
	uchar	RaidNum;	/* Raid Host Adapter Number		*/
};

enum {	/* Read Config Bits */
	/* Byte 9 */
	OverLapCmds	= 0x01,	/* Overlapped Cmds Supported		*/
	TargetMode	= 0x02,	/* SCSI Target Mode Supported		*/
	TrunNotNec	= 0x04,	/* Truncate Command Not Supported	*/
	MoreSupported	= 0x08,	/* More Command Supported		*/
	MAsupported	= 0x10,	/* DMA Mode Supported			*/
	DMAvalid	= 0x20,	/* DMA Channel Field Is Valid.		*/
	ATAdevice	= 0x40,	/* This Is An ATA Device		*/
	HBAvalid	= 0x80,	/* HBA field Is Valid			*/
	/* Byte 30 */
	IRQn		= 0x0F,	/* IRQ Number				*/
	IRQt		= 0x10,	/* IRQ Trigger: 0 = Edge, 1 = Level	*/
	Secondary	= 0x20,	/* Controller Not At Address 0x170	*/
	DMAchan		= 0xD0,	/* DMA Channel Index For ISA		*/
	/* Byte 32 */
	Disable		= 0x01,	/* ISA I/O Address Disabled		*/
	ForceAddr	= 0x02,	/* PCI Forced To An EISA/ISA Addr	*/
	SG64K		= 0x04,	/* 64K of SG space			*/
	SGUAE		= 0x08,	/* Supports unaligned SG Table		*/
	/* Byte 33 */
	MaxID		= 0x1F,	/* Maximun SCSI Target ID Supported	*/
	MaxChan		= 0xE0,	/* Maximun Channel Number Supported	*/
	/* Byte 35 */
	AutoTerm	= 0x08,	/* Support auto term (low byte)		*/
	PCIM1		= 0x10,	/* PCI M1 chipset			*/
	RIDQ		= 0x20,	/* Raid ID may be questionable		*/
	PCIbus		= 0x40,	/* PCI Adapter Flag			*/
	EISAbus		= 0x80,	/* EISA Adapter Flag			*/
};

typedef struct Target Target;
struct Target {
	QLock;
	Rendez;
	int	done;
	int	senval;			/* Sense data valid		*/
	uchar	sense[SenLen];		/* Sense data			*/
	EATAcp;				/* Command Packet		*/
	uchar	ctlrStatus;
	uchar	scsiStatus;
};

typedef struct Ctlr Ctlr;
struct Ctlr {
	Lock;
	int	port;			/* base port			*/
	int	channel;		/* Controller Channel Number	*/
	DPTcfg;				/* Controller Configuration	*/
	DPTstat;			/* Status Packet		*/
	PCIcfg; 			/* PCI info			*/
	Target	target[NTarget];	/* CCP's in use			*/
};
static Ctlr ctlr[Nctl];

static long
LongEndCvt(long x)
{
	long t;
	char *p = (char *) &t;

	*p++ = (x>>24) & 0xFF;
	*p++ = (x>>16) & 0xFF;
	*p++ = (x>>8) & 0xFF;
	*p = x & 0xFF;

	return t;
}

static short
ShortEndCvt(short x)
{
	short t;
	char *p = (char *) &t;

	*p++ = (x>>8) & 0xFF;
	*p = x & 0xFF;

	return t;
}

#ifdef DEBUG
static void
printinfo(Ctlr *cp)
{
	print("\nVendor ID: 0x%x\tDevice ID: 0x%x\tBase Address: 0x%x\n",
		cp->vid, cp->did, cp->baseaddr[0] & ~0x01);
	print("Signiture: %x\tIRQ: %d\t\t\tDMA: %d\n",
		LongEndCvt(cp->EATAsig), cp->byte30 & IRQn,
		cp->byte30 & DMAchan);
	print("CtlrChan0ID: %d\t\tCtlrChan1ID: %d\t\tCtlrChan2ID: %d\n",
		cp->Chan0, cp->Chan1, cp->Chan2);
	print("MaxChanID: %d\t\tMaxChanNum: %d\t\tInterrupt Vector: %d\n\n",
		cp->byte33 & MaxID, cp->byte33 & MaxChan, Int0vec);
}
#endif

static void
dptcmd(int port, ulong ccpaddr)
{
	ulong paddr;

	paddr = PADDR(ccpaddr);
	outb(port+CP0, paddr & 0xFF);
	outb(port+CP1, (paddr>>8) & 0xFF);
	outb(port+CP2, (paddr>>16) & 0xFF);
	outb(port+CP3, (paddr>>24) & 0xFF);
	outb(port+Cmd, SendCP);
}

static int
done(void *arg)
{
	return ((Target *)arg)->done;
}

static int
dptio(int bus, Scsi *p, int rw)
{
	Ctlr *cp = &ctlr[bus];
	Target *tp = &cp->target[p->target];
	EATAcp *ccp = tp;
	ulong len;
	ushort status;
	int x;

	qlock(tp);
	if (waserror())
	{
		qunlock(tp);
		nexterror();
	}

	/*
	 * If this is a request-sense and there is valid sense data
	 * from the loas command, return it immediately.
	 */

	if (p->cmd.base[0] == ScsiExtsens && tp->senval)
	{
		len = tp->ReqSenLen;
		memmove(p->data.ptr, tp->sense, len);
		p->data.ptr += len;
		tp->senval = 0;
		qunlock(tp);
		poperror();
		return 0x6000;
	}

	/*
	 * Fill in the ccp
	 */
	memset(ccp, 0, sizeof(EATAcp));
	ccp->control |= (rw == ScsiIn ? DataIn : DataOut) | ReqSen;
	ccp->device = (cp->channel<<5) | (p->target & id);
	ccp->ReqSenLen = SenLen;
	ccp->dataDMA = LongEndCvt(PADDR(p->data.base));
	ccp->DTL = LongEndCvt(p->data.lim - p->data.base);
	ccp->statDMA = LongEndCvt(PADDR(&cp->DPTstat));
	ccp->reqDMA = LongEndCvt(PADDR(tp->sense));
	ccp->ReqSenLen = SenLen;
	ccp->va = (ulong) tp;
	ccp->msg[0] |= (p->lun & MsgLun) | MsgDisPri | MsgIdent;
	len = p->cmd.lim - p->cmd.base;
	memmove(ccp->CDB, p->cmd.base, len);

	/*
	 * Send the request
	 */
	x = splhi();
	tp->done = 0;
	dptcmd(cp->port, (ulong) ccp);
	splx(x);

	/*
	 * Wait for the request to complete.
	 */
	tsleep(tp, done, tp, 60*5*1000);
	if (tp->done == 0)
		print("dpt%d: timeout cmd=#%2.2ux\n", p->target, p->cmd.base[0]);

	switch (tp->ctlrStatus)
	{
		case 0x00:	/* no error	*/
			status = 0x6000 | tp->scsiStatus;
			p->data.ptr = p->data.lim;	/* assume no residue */
			break;
		case 0x01:	/* selection timed out	*/
			status = 0x20;
			break;
		default:	/* controller error	*/
			status = 0x1000 | tp->ctlrStatus;
			break;
	}
	qunlock(tp);
	poperror();

	return status;
}

static int
dptexec(Scsi *p, int rw)
{
	Ctlr *cp = &ctlr[0];

	if (cp->port == 0)
		error(Enodev);
	if (p->target == cp->Chan0)
		return 0x6002;	/* controller ID */

	return p->status = dptio(0, p, rw);
}

static void
interrupt(Ureg *ur, void *a)
{
	Ctlr *cp = &ctlr[0];
	Target *tp;

	USED(ur, a);

	if (active.machs > 1)
		lock(cp);

	/*
	 * Check the interrupt.
	 */
	if ((cp->info & EOC) == 0)
		return;

	/*
	 * Get ccb address, status information, and set flags.
	 */
	tp = (Target *) cp->va;
	if (tp == 0)
		panic("DPT: no target for ccb #%lux\n", tp);
	tp->ctlrStatus = cp->info & CS;
	tp->scsiStatus = cp->sbs;
	cp->info &= ~EOC;
	tp->done = 1;
	if (tp->scsiStatus == 0x02)
		tp->senval = 1;	/* indicate command returned sense data */
	wakeup(tp);

	inb(cp->port+SR);	/* clear the interrupt			*/
	if (active.machs > 1)
		unlock(cp);
}

static ISAConf dpt3334 =
{
	"dpt3334",
	0,
	0,
	0,
	0,
};

/*
 * Locate the SCSI controller PCI cards.
 */
static Ctlr*
locate(void)
{
	Ctlr *cp = &ctlr[0];
	static int devno;
	int i;

	for(i = 0; i < Nctl; ++i)
	{
		cp = &ctlr[i];
		memset(cp, 0, sizeof(Ctlr));
		cp->vid = PCIvid;
		cp->did = PCIdid;
		if((devno = pcimatch(0, devno, cp)) == -1)
			break;	/* no boards found */
		cp->port = cp->baseaddr[0] & ~0x01;
		dpt3334.port = cp->port;
		dpt3334.irq = cp->irq;
	}
	if (cp->port) return &ctlr[0]; /* always return the 1st board found */

	return 0;
}

int (*
dpt3334reset(void))(Scsi*, int)
{
	Ctlr *cp;
	EATAcp *ccp;
	int x;

	/*
	 * Is the adapter configured?
	 */
	if (isaconfig("scsi", 0, &dpt3334) == 0)
		return 0;

	/*
	 * Assume one controller.
	 */
	if ((cp = locate()) == 0)
		return 0;

	/*
	 * Do a Read Vital Data Page SCSI command
	 * to get the configuration information
	 * instead of using a Read Config Command.
	 * This will cause an interrupt, but which
	 * one isn't known yet.
	 */
	ccp = &cp->target[CtrlID].EATAcp;
	ccp->control |= (Interpret | DataIn | ReqSen);
	ccp->dataDMA = LongEndCvt(PADDR(&cp->DPTcfg));
	ccp->DTL = LongEndCvt(sizeof(DPTcfg));
	ccp->statDMA = LongEndCvt(PADDR(&cp->DPTstat));
	ccp->va = (ulong) &cp->target[CtrlID];
	ccp->msg[0] |= MsgIdent;
	ccp->CDB[0] = ScsiInquiry;	/* SCSI Command	*/
	ccp->CDB[1] |= 0x01;		/* SCSI Extent	*/
	ccp->CDB[2] = 0xC1;		/* SCSI Page	*/
	ccp->CDB[7] = sizeof(DPTcfg);	/* Data Length	*/
	x = splhi();
	dptcmd(cp->port, (ulong) ccp);
	while ((inb(cp->port+ASR)&IRQ) == 0) ;
	inb(cp->port+SR);		/* Clear interrupt */
	splx(x);

	setvec(Int0vec+(cp->byte30 & IRQn), interrupt, cp);
	outb(cp->port+Cmd, Reset);	/* Reset Controller and SCSI Bus */
	delay(5000);
#ifdef DEBUG
	printinfo(cp);
#endif

	return dptexec;
}